aluminum alloy

發布時間：2025-08-24 | 來源：互聯網轉載和整理

鋁合金

雙語例句

Built two product lines of metal powder and aluminum alloy additive 、 metal additive, grain refiner. 建立了金屬粉末和鋁熔鑄業用熔劑、金屬添加劑、細化劑兩套生產線。

Valve body and internal parts: anodized aluminum alloy, copper. 閥體和內部零件：陽極電鍍鋁合金、銅。加固端蓋：塑料。

The dimensional change of2A12 aluminum alloy by microarc oxidation in silicate electrolyte has been investigated. 研究了2A12鋁合金在硅酸鹽電解液中微弧氧化的尺寸變化。

The relationship of the heat deformation processes of the antirust aluminum alloy LF6 and its microstructure were studied. 研究了防銹鋁合金LF6熱變形工藝對組織的影響。

Effect of ingot gas holes on the structure and performance of 4032 aluminum alloy 鑄錠氣孔對4032鋁合金組織和性能的影響

This paper discussed the application of artificial neural network at the resistance spot welding of aluminum alloy. 針對鋁合金的電阻點焊，研究了人工神經網絡在點焊質量估測中的應用。

The effect of aging temperature and aging time to new-type heat-resisting aluminum alloy forging structure and properties are introduced. 通過對新型鋁合金時效處理后的組織結構進行分析，研究了不同的時效溫度和時間對該鋁合金力學性能的影響。

The coating behavior of aluminum alloy lost foam casting ( LFC) process has been investigated. 研究了鋁合金消失模鑄造過程中的涂料行為。

The effect of isothermal forging temperature on microstructure and mechanical properties of2B70 aluminum alloy was studied. 研究了不同等溫鍛造溫度對2B70鋁合金顯微組織與力學性能的影響。

Successful development of the market's leading aluminum and aluminum alloy surface treatment technology. 成功的開發出了市場上領先的鋁、鋁合金的表面處理技術。

The cupping value of lubricated aluminum alloy sheet is studied by BCS-30D general sheet metal test machine. 在BCS-30D通用板材成形性試驗機上，對鋁合金薄板的杯突值進行了不同潤滑條件的試驗研究。

The effect of pulsed current and pulsed magnetic field on the solidification structures of LY12 aluminum alloy was studied. 在LY12鋁合金凝固的過程中施加脈沖電流或脈沖磁場，研究脈沖電流或脈沖磁場對這種合金凝固組織的影響。

Resistance spot welding of aluminum alloy with great resistance medium; 介紹了在實驗室中測大電阻的一種方法。

The wear patterns and wear mechanisms of solid cemented carbide are ***yzed in high-speed milling of aluminum alloy. 對硬質合金整體立銑刀高速銑削加工航空鋁合金時的刀具磨損形態及其磨損機理進行了觀察和分析。

Effects of Aging Temperature and Mg Content on the Microstructure and Corrosive Properties of a High-Mg Aluminum Alloy 時效溫度和鎂含量對高鎂鋁合金微觀組織和腐蝕性能的影響

The effects of various process variables on the density of aluminum alloy castings have been investigated systematically. 系統研究了各工藝因素對干砂消失模鑄鋁件密度的影響。

Head and cap are machined from aluminum alloy. 頭部和上限從鋁合金加工。

The rear armrests and the rear backrest support are made in aluminum alloy. 后扶手和后靠背支架為鋁合金制作。

The product quality carbon structural steel, zinc-plated aluminum alloy made from rare earth. 該產品采用優質碳素結構鋼，表面鍍稀土鋅鋁合金制造而成。

A new green sealing process of anodic oxide film of aluminum alloy was studied in this paper. 本文研究了一種鋁合金陽極氧化膜新型的綠色封閉工藝。

A process of forming chemical conversion coatings on LY12 hard aluminum alloy in cerium salt solutions was advanced. 提出了一種鋁合金鈰鹽化學轉化成膜工藝。

The template body is made of aluminum alloy, steel or copper. 模板體由鋁合金、鋼、銅等金屬之一種制成。

The influences of welding parameters on the weld appearance of friction stir welding of LY12 aluminum alloy were researched. 研究了攪拌摩擦焊工藝參數對LY12鋁合金焊縫形貌的影響。

The reasons of porosities production and process instability in CO2 laser welding shipbuilding T-section aluminum alloy are also discussed. 同時，討論了船用鋁合金T型材CO2激光焊接過程中產生氣孔和過程不穩定的原因。

Application: aluminum alloy, copper alloy, magnesium alloy. 適用：鋁合金、銅合金、鎂合金。

The microstructure evolutions during spray forming process for high magnesium aluminum alloy are investigated in this paper. 研究了高鎂鋁合金在噴射成形過程中顯微組織的變化。

Good adhesion to steel, galvanized steel and aluminum alloy. 對鋼鐵、鋅鋼材及鋁合金有良好的附著力。

CAE ***ysis and orthogonal design are applied in aluminum alloy housing die-casting process optimization design. 采用CAE方法和正交分析法對鋁合金支架壓鑄件的壓鑄工藝進行了優化設計。

It is applicable to the various brazing between aluminum alloy and aluminum alloy, aluminum alloy and Stainless steels. 鋁基釬料適用于鋁合金、鋁合金與不銹鋼之間的釬焊。